Chrysler 2007 300 SRT8 Owner'S Manual Download Page 11 | Manualshive

Page: 11 / 360

Chrysler 2007 300 SRT8 Owner'S Manual Download Page 11

A WORD ABOUT YOUR KEYS

You can insert the double-sided keys into the locks with
either side up.

The dealer that sold you your new vehicle has the key
code numbers for your vehicle locks. These numbers can
be used to order duplicate keys from your dealer. Ask
your dealer for these numbers and keep them in a safe
place.

Ignition Key Removal

The shift lever must be in PARK. Turn the key to the
LOCK position, and then remove the key.

NOTE:

The power window switches, radio, power

sunroof (if equipped), and power outlets will remain
active for up to 60 minutes after the ignition switch is
turned off. Opening either front door will cancel this
feature. The time for this feature is programmable. For
details, refer to “Delay Power Off to Accessories Until

Vehicle Key

Ignition Key Positions

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

11

2

«
...
9
10
11
12
13
...
»

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments