manualshive.com logo in svg

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 29 / 360

Share
Download
Chrysler 2007 300 SRT8 Owner'S Manual Download Page 29

TRUNK SAFETY WARNING

WARNING!

Do not allow children to have access to the trunk,
either by climbing into the trunk from outside, or
through the inside of the vehicle. Always close the
trunk lid when your vehicle is unattended. Once in
the trunk, young children may not be able to escape,
even if they entered through the rear seat. If trapped
in the trunk, children can die from suffocation or
heat stroke.

Trunk Emergency Release

The trunk of your vehicle is equipped with an emergency
release handle. It is located on the inside of the trunk lid,
near the latch, and is coated so that it glows in a darkened
trunk. Pull on the handle to open the trunk.

Emergency Release

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

29

2

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments