Home
/
Chrysler
/
2007 300 SRT8
/
Owner'S Manual

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 142 / 360

Share

Page: 142 / 360

Chrysler 2007 300 SRT8 Owner'S Manual Download Page 142

Please note that the TPMS is not a substitute for proper
tire maintenance, and it is the driver’s responsibility to
maintain correct tire pressure, even if under-inflation has
not reached the level to trigger illumination of the TPMS
low tire pressure telltale.

The Tire Pressure Monitoring Telltale Light will illumi-
nate in the instrument cluster, and an audible chime will
be activated when one or more tire pressures is low. The
Tire Pressure Monitoring Telltale Light will flash on and
off for 60 seconds when a system fault is detected. The
flash cycle will repeat every ten minutes or until the fault
condition is removed and reset. (See page 239 for more
information.)

CAUTION!

The TPMS has been optimized for the original
equipment tires and wheels. TPMS pressures and
warning have been established for the tire size
equipped on your vehicle. Undesirable system op-
eration or sensor damage may result when using
replacement equipment that is not of the same size,
type, and/or style. After-market wheels can cause
sensor damage. Do not use tire sealant from a can, or
balance beads if your vehicle is equipped with a
TPMS, as damage to the sensors may result.

23. Voltage Light

This light monitors the electrical system volt-
age. The light should turn on momentarily as

the engine is started. If the light stays on or turns on
while driving, it indicates a problem with the charging
system. Immediate service should be obtained.

142

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
140
141
142
143
144
...
»

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments