manualshive.com logo in svg

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 282 / 360

Share
Download
Chrysler 2007 300 SRT8 Owner'S Manual Download Page 282

WARNING!

•

Battery fluid is a corrosive acid solution and can
burn or even blind you. Don’t allow battery fluid
to contact your eyes, skin, or clothing. Don’t lean
over a battery when attaching clamps. If acid
splashes in eyes or on skin, flush the area imme-
diately with large amounts of water.

•

Battery gas is flammable and explosive. Keep
flame or sparks away from the battery. Don’t use
a booster battery or any other booster source with
an output greater than 12 volts. Don’t allow cable
clamps to touch each other.

•

Battery posts, terminals, and related accessories
contain lead and lead compounds. Wash hands
after handling.

•

The battery in this vehicle has a vent hose that
should not be disconnected and should only be
replaced with a battery of the same type (vented).

CAUTION!

•

It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to
the negative post. Battery posts are marked posi-
tive (+) and negative (-) and identified on the
battery case. Cable clamps should be tight on the
terminal posts and free of corrosion.

•

If a “fast charger” is used while battery is in
vehicle, disconnect both vehicle battery cables
before connecting the charger to battery. Do not
use a “fast charger” to provide starting voltage.

Air Conditioner Maintenance

For best possible performance, your air conditioner
should be checked and serviced by an Authorized Dealer
at the start of each warm season. This service should
include cleaning of the condenser fins and a performance
test. Drive belt tension should also be checked at this
time.

282

MAINTAINING YOUR VEHICLE

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments