Chrysler 2007 300 SRT8 Owner'S Manual Download Page 313

Page: 313 / 360

4. Push the replacement bulb into the socket assembly.

5. Reinstall the bulb and socket assembly.

6. Reattach the light to the rear fascia, and then install the
screws.

FLUIDS AND CAPACITIES

U.S.

Metric

Fuel (approximate)
6.1 Liter Engine

19 gal-

lons

72 liters

Engine Oil with Filter

6.1 Liter Engine (SAE 0W-40)

7 qts.

6.6 liters

Cooling System *

6.1 Liter Engine (Mopar

威

Antifreeze/Coolant 5 Year/

100,000 Mile Formula) or

equivalent.

15.2 qts

14.4 li-

ters

* Includes heater and coolant recovery bottle filled to
MAX level.

MAINTAINING YOUR VEHICLE

313

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Search results

Summary of Contents for 2007 300 SRT8

Reviews:

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 313 / 360

Search results

Summary of Contents for 2007 300 SRT8

Reviews: