Home
/
Chrysler
/
2007 300 SRT8
/
Owner'S Manual

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 124 / 360

Share

Page: 124 / 360

Chrysler 2007 300 SRT8 Owner'S Manual Download Page 124

Settings (Customer Programmable Features),” under
“Electronic Vehicle Information Center (EVIC)” in Sec-
tion 4 of this manual.

Sunroof Fully Closed

Press the switch forward and release to ensure that the
sunroof is fully closed.

ELECTRICAL POWER OUTLETS

There are two 12-volt electrical outlets on this vehicle.
Both of the outlets are protected by a fuse.

The 12-volt power outlet next to the ash receiver tray (if
equipped with an optional Smoker’s Package) has power
available only when the ignition is on. This outlet will
also operate a conventional cigar lighter unit.

WARNING!

Do not place ashes inside the cubby bin located on
the center console on vehicles not equipped with the
ash receiver tray. A fire leading to bodily injury
could result.

NOTE:

If desired, the power outlet next to the ash

receiver tray (if equipped) can be converted by your
authorized dealer to provide power with the ignition
switch in the LOCK position.

Front Power Outlet

124

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
122
123
124
125
126
...
»

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments