manualshive.com logo in svg

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 191 / 360

Share
Download
Chrysler 2007 300 SRT8 Owner'S Manual Download Page 191

REAR WINDOW FEATURES

Electric Rear Window Defroster

The electric Rear Window Defroster Control is
located on the climate control. Press this button to

turn on the rear window defroster and the heated side
mirrors (if equipped). An LED in the button will illumi-
nate when the rear window defroster is ON. The de-
froster automatically turns off after approximately 10
minutes of operation for the first push of the button, and
will turn off after approximately 5 minutes for the second
push of the button.

CAUTION!

To avoid damaging the electrical conductors of the
rear window defroster, do not use scrapers, sharp
instruments, or abrasive window cleaners on the
interior surface of the window.

Labels can be peeled off after soaking with warm
water.

UNDERSTANDING YOUR INSTRUMENT PANEL

191

4

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments