manualshive.com logo in svg

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 254 / 360

Share
Download
Chrysler 2007 300 SRT8 Owner'S Manual Download Page 254

EXAMPLE ONLY

Front
Axle

Rear Axle

Empty Weight

2054 lbs
(932 kg)

1805 lbs

(819 kg )

Load (Including driver, pas-
sengers, and cargo)

271 lbs

(123 kg)

579 lbs

(263 kg)

Total

2325 lbs

(1055 kg)

2384 lbs

(1081 kg)

GAWR

2546 lbs

(1155 kg)

2708 lbs

(1228 kg)

NOTE:

Refer to the “Vehicle Certification Label” at-

tached to the rear of the driver’s door for your vehicle’s
GVWR and GAWRs. This table is only an example.

TRAILER TOWING

Trailer towing with this vehicle is not recommended.

RECREATIONAL TOWING (BEHIND
MOTORHOME, ETC.)
TOWING THIS VEHICLE BEHIND ANOTHER
VEHICLE (Flat towing with all four wheels on the
ground)

Recreational towing for this vehicle is not recommended.

NOTE:

If the vehicle requires towing, make sure all

four wheels are off the ground.

GROUND CLEARANCE

CAUTION!

Damage to the front and rear fascias can occur if you
disregard the low ground clearance in the front and
rear of this vehicle. Pay close attention when parking
to avoid running into parking curbs. Exercise caution
when entering or exiting steep driveways or when
pulling off the road onto soft shoulders.

254

STARTING AND OPERATING

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments