manualshive.com logo in svg

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 302 / 360

Share
Download
Chrysler 2007 300 SRT8 Owner'S Manual Download Page 302

CAUTION!

•

When installing the Power Distribution Center
cover, it is important to ensure the cover is prop-
erly positioned and fully latched. Failure to do so
may allow water to get into the Power Distribu-
tion Center, and possibly result in an electrical
system failure.

•

When replacing a blown fuse, it is important to
use only a fuse having the correct amperage
rating. The use of a fuse with a rating other than
indicated may result in a dangerous electrical
system overload. If a properly rated fuse contin-
ues to blow, it indicates a problem in the circuit
that must be corrected.

Fuses (Rear Power Distribution Center)

There is also a power distribution center located in the
trunk under the spare tire access panel. This center
contains fuses and relays.

Rear Power Distribution Center

302

MAINTAINING YOUR VEHICLE

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments