Chevrolet 2007 Kodiak Owner'S Manual Download Page 107 | Manualshive

Page: 107 / 430

background image

To set a new temporary engine idle speed do the
following:

1. Make sure all of the previously described

conditions are met.

2. Press the accelerator pedal to the desired

engine speed.

3. Momentarily press the manual high idle

switch.

The temporary high idle speed will be set. This
new high idle rpm level will be remembered by the
system until either the ignition is turned to OFF
or a new high idle speed is set.

Automatic High Idle System

The automatic high idle feature will engage
whenever you start your vehicle and the engine is
below the preset operating temperature. This
will help decrease engine warm-up time.

On vehicles that have the Caterpillar

®

diesel

engine you may have an exhaust restrictor that
will operate in High Idle mode. The exhaust brake
switch must be on for this feature to operate.
See

Diesel Engine Exhaust Brake on page 112

for

more information.

Idle speed will then return to normal under any of
the following conditions:

•

The engine reaches the preset operating
temperature or has been operating for at least
10 minutes.

•

The brake pedal is pressed.

•

The manual transmission clutch pedal is
pressed or, if the vehicle has automatic
transmission, it is shifted from NEUTRAL (N)
or PARK (P).

•

The vehicle speed exceeds about 5 mph
(8 km/h).

•

The throttle is pressed.

107

«
...
105
106
107
108
109
...
»

Summary of Contents for 2007 Kodiak















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Kodiak

2011 Corolla LE

Brand: Toyota Pages: 19

Brand: Porsche Pages: 195

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: Van Guard Pages: 3

Brand: Yakima Pages: 12

Brand: FALCON RIDGE Pages: 6

Brand: Sanitas Pages: 36

Brand: Atera Pages: 3

Brand: Black Horse Pages: 5

Brand: PUTCO Pages: 2

Brand: Huf Pages: 6

Brand: ULTIMATE SPEED Pages: 56

Brand: Whispbar Pages: 14

Brand: Honda Pages: 279

Brand: Kargo Master Pages: 10

PRIME DESIGN HRR-NV11B

Brand: Safe Fleet Pages: 12

1996 Civic Del Sol

Brand: Honda Pages: 219

Brand: Road Ranger Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands