Chevrolet 2007 Kodiak Owner'S Manual Download Page 127 | Manualshive

Page: 127 / 430

background image

Vehicles built for use as tractors or towing
vehicles have two air brake controls. They look
like this:

{

CAUTION:

When the yellow PARKING BRAKE and
the red TRAILER AIR SUPPLY knobs are
both pushed in, your rig will be free to
move. It could strike someone or
something. When both of these knobs are
pushed in, hold the regular brake pedal
down to keep your rig from moving.

To charge a trailer’s air brake system do the
following:

1. Move your vehicle into the proper position.

2. Apply the parking brake by pulling the yellow

parking brake knob out.

3. Hook up the trailer air system properly.

4. Get into the vehicle.

5. Push and hold down the regular brake pedal.

6. Push in both the yellow parking brake and

the red trailer air supply knobs. This will
charge your trailer’s air system.

After a few minutes, the trailer system should be
fully charged. When it is, the air pressure gage will
show about 125 to 135 psi (862 to 931 kPa).
See

Air Pressure Gage on page 183

for more

information.

127

«
...
125
126
127
128
129
...
»

Summary of Contents for 2007 Kodiak















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Kodiak

Brand: Accel Pages: 2

Brand: TATA Motors Pages: 161

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Brand: UltraGauge Pages: 55

Brand: Yakima Pages: 6

Brand: Yakima Pages: 18

Brand: Veigel Pages: 24

Brand: Cellular Line Pages: 25

Brand: CALIMA Pages: 9

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Brand: Dakota Digital Pages: 3

Brand: Ford Pages: 8

Brand: Intec Pages: 16

Brand: Great Wall Pages: 18

Brand: WIX Pages: 2

Akerstroms Tx700

Brand: LXE Pages: 146

Brand: Linear Logic Pages: 8

Brand: Edelbrock Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands