Chevrolet 2007 Kodiak Owner'S Manual Download Page 99 | Manualshive

Page: 99 / 430

background image

Gasoline Engine Warm-Up

When you have started your engine, let it run for
20 or 30 seconds to warm up before you put a
load on the engine.

Drive at moderate speeds for the first 2 to 3 miles
(3.2 to 4.8 km), especially in cold weather. See

High Idle System on page 106

.

Restarting the Gasoline Engine While
Moving (Automatic Transmission)

If you have to restart the engine while the
vehicle is moving, you will first have to shift to
NEUTRAL (N). This safety feature prevents
starting the engine when the transmission is in a
drive gear.

Stopping the Gasoline Engine

Let your engine idle for a few seconds before
turning it off after you have finished driving your
vehicle.

If you shift to NEUTRAL (N) or PARK (P), set the
parking brake.

If your vehicle has a two-speed axle, put the
range selector in low. To be sure the axle has
shifted into low, engage the clutch and
transmission; the vehicle may move slightly
when you do this.

While your engine is idling and before you turn it
off, you can make a list of any operational or
handling concerns to give to responsible
maintenance personnel so they can handle them
right away.

Moisture will condense in a fuel tank that is almost
empty if the engine has not run for a while,
even just overnight under some conditions. So, it
is always best to refuel your vehicle at the end
of each run.

99

«
...
97
98
99
100
101
...
»

Summary of Contents for 2007 Kodiak















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Kodiak

Brand: AA Products Pages: 6

witty park XEV6 Series

Brand: hager Pages: 9

Brand: Vauxhall Pages: 177

Brand: NanoCam Plus Pages: 32

Brand: Oldsmobile Pages: 354

Brand: v.link Pages: 12

Brand: S3 Power Sports Pages: 2

2004 Impreza OUTBACK SPORT

Brand: Subaru Pages: 34

S90 - ACCESSORY PANEL

Brand: Volvo Pages: 166

K40 Platinum360

Brand: K40 ELECTRONICS Pages: 11

Brand: Cadillac Pages: 19

Brand: Summit Racing Pages: 11

Brand: Meritor Pages: 20

SB-J-GCHER2/10W3v2

Brand: Stealthbox Pages: 2

Brand: Buick Pages: 20

Brand: Vauxhall Pages: 4

Electronic Parking Disc 3

Brand: Jacob Jensen Pages: 17

Brand: Kargo Master Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands