Chevrolet 2007 Kodiak Owner'S Manual Download Page 124 | Manualshive

Page: 124 / 430

background image

Shifting Out of NEUTRAL

To shift the transfer case out of NEUTRAL, do the
following:

1. Set the parking brake and apply the regular

brake pedal.

2. Turn the ignition to RUN with the engine off.

3. Put the transmission in NEUTRAL (N).

4. Turn the transfer case knob to the desired

shift position (Two-Wheel High, Four-Wheel
High, Four-Wheel Low).

5. After the transfer case has shifted out of

NEUTRAL, the indicator light goes out.

Notice:

Driving with the parking brake on can

overheat the brake system and cause
premature wear or damage to brake system
parts. Verify that the parking brake is fully
released and the brake warning light is
off before driving.

6. Release the parking brake.

7. Start the engine and shift the transmission

lever to the desired position.

Excessively shifting the transfer case into or out of
the different modes can cause the transfer case
to enter the shift protection mode. This protects the
transfer case from possible damage and only
allows the transfer case to respond to one shift per
10 seconds. The transfer case can stay in this
mode for up to three minutes.

124

«
...
122
123
124
125
126
...
»

Summary of Contents for 2007 Kodiak















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Kodiak

2016 Sandero Stepway

Brand: Renault Pages: 183

Q Access Alpha GSE 2023

Brand: Q Mobility Group Pages: 9

Brand: ideus Pages: 159

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

Bluetooth Phone System 2010

Brand: Kia Pages: 16

Brand: Toyota Pages: 295

Brand: Lexus Pages: 830

Brand: Grillo Pages: 71

Brand: Cadillac Pages: 19

1999 Crown Victoria

Brand: Ford Pages: 208

Brand: Cadillac Pages: 48

Brand: Subaru Pages: 786

Brand: Mercedes-Benz Pages: 434

Brand: Genesis Pages: 30

Brand: NavInc Pages: 5

Brand: BMW Pages: 386

Brand: PAC Pages: 4

Brand: Husky Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands