Chevrolet 2007 Kodiak Owner'S Manual Download Page 301 | Manualshive

Page: 301 / 430

background image

Electric Air Compressor

Your vehicle may have an electric air compressor.
This compressor is used to run options that
require pressurized air, such as an air horn, air
seat, 7.8L engine exhaust restrictor, or 7.8L engine
exhaust brake.

The air compressor is used when vehicles do not
have an air brake system.

The air supply for
this system must be
maintained by releasing
the drain valve to eject
any moisture that
may have built up in
the system.

It is recommended that this system be drained on
a weekly basis.

Clutch Pedal Free Travel

If you have a V8 engine and a manual
transmission, the clutch will need adjustment
when pedal free travel gets down to about 1/4 inch
(6 mm), as measured at the clutch pedal pad.
You should have 1 1/2 to 2 inches (38 to 51 mm)
of clutch pedal free travel.

If the clutch ever needs service, be sure to use
only GM clutch replacement parts.

Chassis Lubrication

Your Maintenance Schedule provides all of the
required chassis lubrication intervals and identifies
proper lubricants to use. Be sure to see the
Maintenance Schedule before performing any
chassis lubrication service. To determine location of
chassis lubrication items, use the following charts.

301

«
...
299
300
301
302
303
...
»

Summary of Contents for 2007 Kodiak















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Kodiak

Brand: Jeda Pages: 8

Brand: Jeep Pages: 496

Brand: Vintage Air Pages: 28

Brand: Yakima Pages: 12

Autostacker PL-6SR

Brand: BendPak Pages: 104

Brand: STC Pages: 6

Brand: Cadillac Pages: 407

Brand: Caltrend Pages: 3

Fleetwood Brougham Sedan 1966

Brand: Cadillac Pages: 56

Brand: Bilstein Pages: 7

Brand: Aston Martin Pages: 415

Brand: Volkswagen Pages: 68

1995 Roadmaster

Brand: Buick Pages: 340

Brand: Front Runner Pages: 7

Brand: Painless Performance Pages: 16

Brand: EUFAB Pages: 8

Brand: Whispbar Pages: 15

Brand: Vauxhall Pages: 253

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands