manualshive.com logo in svg

Chevrolet 2007 Kodiak, Owner'S Manual

The Chevrolet 2007 Kodiak is a reliable heavy-duty truck designed for commercial use. Ensure optimal performance and maintenance by downloading the free Owner's Manual from manualshive.com. This comprehensive manual provides detailed instructions and key insights to safely operate and maintain the Chevy Kodiak.

Share
Download
background image

•

If the engine coolant temperature gage needle
goes into the hot area on the gage, stop the
engine and find the cause of the overheating.
See

Engine Coolant Temperature Gage on

page 173

for more information.

•

If you have air brakes, the dual-needle air
pressure gage should read at least 115 psi
(790 kPa) for both service systems before you
try to move the vehicle. When air pressure
is below 60 psi (420 kPa), the LOW AIR light
will come on and you will hear a tone
alarm. See

Brake System Warning Light on

page 169

for more information. If the pressure

does not build up or drops during warm-up,
stop the engine and find the cause before you
try to move the vehicle. Recommended air
pressure before driving is 120 psi (830 kPa).
See

Air Pressure Gage on page 183

for

more information.

•

The charging system light should come on
when the ignition key is turned to RUN or
START and should go out when the engine is
running above idle. If the light does not go
out or comes back on during normal engine
operation, have the charging system checked
right away. (This light tells you if the

generator is not charging; it does not reflect
the condition of the battery.) See

Charging

System Light on page 167

for more

information.

•

The voltmeter charge indicator gage tells you
the condition of your battery’s charge. The
gage should be in the center area during
engine operation. The red area on the
left indicates an undercharge condition; the
red area on the right indicates an overcharge.
If the gage is in either red area, have the
battery and charging system checked
right away. See

Voltmeter Gage on page 168

for more information.

Notice:

Do not allow the engine to operate at

low idle for more than five minutes. This
can cause low engine operating temperatures
which can affect engine operation and
reduce engine life. Engine idle speed should
be increased to 1200 rpm whenever extended
idle is required. Once started, the engine
should be placed under load to allow the
engine coolant temperature to reach 150°F
(66°C) before shutting off the engine.

110

Summary of Contents for 2007 Kodiak















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Kodiak

iDataLink ADS-ALCA Install Manuals preview
ADS-ALCA
Brand: iDataLink Pages: 30
DAVIS 8126GD User Manual preview
8126GD
Brand: DAVIS Pages: 32
Edelbrock 6883 Instructions preview
6883
Brand: Edelbrock Pages: 2
Nav TV NAV-INREN Quick Manual preview
NAV-INREN
Brand: Nav TV Pages: 2
Great Wall WEY VV5 Service Manual preview
WEY VV5
Brand: Great Wall Pages: 18
WIX WP9378 Installation Instruction preview
WP9378
Brand: WIX Pages: 2
Radical Sportscars SR 3 SL Owner'S Handbook Manual preview
SR 3 SL
Brand: Radical Sportscars Pages: 44
MAcarbon MAA.R8.06 Install Instructions preview
MAA.R8.06
Brand: MAcarbon Pages: 3
Hama 00173884 Operating Instructions Manual preview
00173884
Brand: Hama Pages: 13
Rydeen BSS2 Owner'S Manual preview
BSS2
Brand: Rydeen Pages: 14
Porsche 928 GTS 1994 Owner'S Manual preview
928 GTS 1994
Brand: Porsche Pages: 127
Scion 2013 iQ Warranty & Maintenance Manual preview
2013 iQ
Brand: Scion Pages: 58
AUTOTECH 10.109.405K Installation Instructions preview
10.109.405K
Brand: AUTOTECH Pages: 2
Harbor Freight Tools 95058 Installation And Operation Instructions Manual preview
95058
Brand: Harbor Freight Tools Pages: 8
RAWLINK 36772 Instruction Manual preview
36772
Brand: RAWLINK Pages: 25
Axxess OESWC-7552-STK Installation Instructions Manual preview
OESWC-7552-STK
Brand: Axxess Pages: 8
Diono easy view XXL Instructions Manual preview
easy view XXL
Brand: Diono Pages: 9
Chevrolet 2003 TraiIBIazer Owner'S Manual preview
2003 TraiIBIazer
Brand: Chevrolet Pages: 426

Brands by name

Popular brands

Load more brands