Champion UH130 M4 Installation And Operation Manual Download

Page: 29 / 166

Model UH130, UH130B, UH230, UH230B - Installation

Pumps and Injection Points - Detergent and Rinse-aid Dispensing Pumps

UH130, UH130B and UH230, UH230B

UH130, UH130B Control Panel

WASH

RINSE

PRIME

DETERGENT

RINSE AID

OFF/DRAIN

POWER

START

TEMPERATURE

1 8 0

1 5 0

1. The chemical dispensing pump supply lines

must be primed before they will pump the

chemicals properly.

2. Make sure the chemical containers are full and

the correct pick-up tubes are in their containers.

3. Turn the dishwasher power switch ON. The

switch will illuminate and the dishwasher

will fill with water.

4. Open the dishwasher door, then push and hold

the prime push button UP to the DETERGENT

position until detergent is observed entering the

wash tank compartment through the fitting located on the back right corner of the tank.

Release the push button.

5. Push and hold the prime push button DOWN to the Rinse-aid position until you see

air bubbles moving through the rinse-aid tubing coming out of the chemical container.

Release the push button.

6. Close the door to complete the priming operation.

PRIME

DETERGENT

RINSE AID

! VERY IMPORTANT !

The chemical dispensing pumps must be primed before operating the dishwasher and

whenever the chemical container is changed.

Priming the Dispensing Pumps

WASH

RINSE

PRIME

EXT WASH

DELIME

DETERGENT

RINSE AID

OFF/DRAIN

POWER

START

TEMPERATURE

1 8 0

1 5 0

UH230, UH230B Control Panel

(continued on next page)

Summary of Contents for UH130 M4







































































































































































Search results

Summary of Contents for UH130 M4

Reviews:

Related manuals for UH130 M4

Brands by name

Popular brands

Champion UH130 M4, Installation And Operation Manual

Search results

Summary of Contents for UH130 M4

Reviews:

Related manuals for UH130 M4

Brands by name

Popular brands