Champion UH130 M4 Installation And Operation Manual Download | Manualshive

Page: 76 / 166

background image

66

NOTE:

The installation of your dishwasher must be performed by qualified service personnel familiar

with food service equipment and must comply with all local health codes.

Problems due to improper installation are not covered by the Limited Warranty.

NOTE:

The installation of the dishwasher must comply with all local electrical, plumbing, health and

safety codes or in the absence of local codes, installed in accordance with the applicable

requirements in the National Electrical Code, NFPA 70, Canadian Electrical Code (CEC),

Part 1, CSA C22.1; and the Standard for Ventilation Control and Fire Protection of

Commercial Cooking Operations, NFPA 96.

Turn to the front of this manual and follow the instructions to register your

product online or by fax.

CAUTION:

Be careful when lifting and moving the dishwasher

to prevent damage to the machine.

NOTE:

The installation of the dishwasher must

comply with local health codes.

NOTE:

The dishwasher front-to-back dimension with the

door open is 42-3/8" [1076 mm]. The clearance

to the back wall is 2" [51mm].

Installation - UH330B

Receiving - UH330B

Counter-top

Wall

2"

[51mm]

Min.

34"

[864cm]

Min.

Floor

42-3/8"

[1076 mm]

Min.

Placement - UH330B

1.  Inspect the outside of the dishwasher carton for signs of damage.
2.  Remove the carton and inspect the dishwasher for damage.
3.  Check for any options or accessories that may have shipped with your dishwasher.
4.  Compare the installation site utility connections with the dishwasher utility connections and

make sure they are the same.

5. The dishwasher can be installed as a free-standing unit or under a counter-top. The typical

counter-top height in most locations is 34" [864 mm]. It is highly recommended that the

underside of the counter-top be clad in metal.

6. Under counter installations should provide storage space for the dishwasher chemical

supply containers. Do not elevate the containers above the finished floor.

7. Chemical supply containers should be placed as close to the machine as possible and

the chemical tubing taped to the back of the machine should be repositioned before

permanently placing the machine.

8. The dishwasher has 4 adjustable feet for leveling.
9. Place the dishwasher in its permanent location. and level it front-to-back and side-to-side.

«
...
74
75
76
77
78
...
»

Summary of Contents for UH130 M4







































































































































































Reviews:

No comments

Related manuals for UH130 M4

Brand: GE Pages: 108

Brand: Haier Pages: 20

Brand: Haier Pages: 43

Brand: Haier Pages: 20

Brand: Haier Pages: 18

Brand: Newworld Pages: 44

Brand: ZANKER Pages: 19

Brand: Hotpoint Ariston Pages: 64

Brand: Insinger Pages: 104

Brand: Hotpoint Pages: 10

Brand: Swissh Pages: 12

Brand: Buffalo Pages: 20

Brand: Infiniton Pages: 67

Brand: Samsung Pages: 48

Brand: Samsung Pages: 22

Brand: Electrolux Pages: 32

Brand: Electrolux Pages: 25

Brand: Electrolux Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands