Champion UH130 M4 Installation And Operation Manual Download Page 24

Page: 24 / 166

Installation - Model UH130B, UH230B

Booster Fill Switch - (Filling the booster tank for the first time)

UH130B and UH230B only

THE BUILT-IN BOOSTER TANK WAS DRAINED BEFORE SHIPMENT AND

MUST BE REFILLED BEFORE OPERATING THE DISHWASHER.

THE BOOSTER FILL SWITCH IS LOCATED BEHIND THE LOWER FRONT PANEL ON THE

RIGHT SIDE OF THE MACHINE.

! CAUTION !

AVOID PERMANENT DAMAGE TO THE BOOSTER HEATER

DO NOT TURN THE DISHWASHER POWER SWITCH

ON WHEN FILLING THE BOOSTER FOR THE FIRST TIME.

To refill the booster for the first time:

1. Turn the main breaker or disconnect switch to the dishwasher ON.
2.

DO NOT PUSH THE DISHWASHER ON-OFF/DRAIN POWER SWITCH TO THE ON POSITION

3. Locate the booster fill switch and note the switch is in the OFF position.

(continued on next page)

Summary of Contents for UH130 M4







































































































































































Search results

Summary of Contents for UH130 M4

Reviews:

Brands by name

Popular brands

Champion UH130 M4, Installation And Operation Manual

Search results

Summary of Contents for UH130 M4

Reviews:

Brands by name

Popular brands