manualshive.com logo in svg

Champion UH130 M4, Installation And Operation Manual

Share
Download
Champion UH130 M4 Installation And Operation Manual Download Page 73

63

Booster Heater/Wash Tank Heater Interlock Circuit Operation - UH130B, UH230B, UH330B

Booster Heater/Wash Tank Heater Interlock Circuit Operation

 

For Models UH130B, UH230B 

The booster heater/wash tank heater interlock circuit removes  

power from the wash tank heater whenever the booster heater contactor energizes.   

The illustration below shows how the booster heater contactor is wired.  
The booster heater contactor is located on the center of the base behind the lower front access 

panel.

Interlock Circuit Operation

1.  The dishwasher fills with water when the main power switch on the dishwasher is turned on. 

The booster heater thermistor calls for heat which energizes the booster heater contactor.  

2.  The auxiliary contact on the top of the contactor opens and removes power from the  

wash tank heater.

3.  When the booster heater thermister is satisfied, the booster heater contactor de-energizes  

and the auxiliary contacts close applying power to the wash tank heater.  

4.  This operation is repeated whenever the booster thermistor calls for heat.

To booster 

heater contactor

1PH

208-230VAC

To

Auxiliary

Contactor

115VAC

No power when booster

heater is connected for 1 PH

No power when booster

heater is connected for 1 PH

L1 

L2 

L3 

N

Main Terminal Block (MTB)

To wash 

tank heater

115VAC

From 

main 

terminal block

115 VAC

From 

main 

terminal block

1 PH

208-230VAC

No power

when booster

heater is

connected for

1 PH

No power when booster

heater is connected for 1 PH

L1

L3

L1

N

L2

To booster heater

1 PH 208-230VAC

1H2

1H3

1H1

Auxiliary 
Contactor

Booster Heater
Contactor

Summary of Contents for UH130 M4







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands