Champion UH130 M4 Installation And Operation Manual Download Page 77

Page: 77 / 166

Model UH330B - Installation

! ATTENTION !

ALL DISHWASHERS ARE SHIPPED FROM THE FACTORY WIRED FOR SINGLE PHASE

OPERATION UNLESS SPECIFIED AT THE TIME OF ORDER.

IF YOU ARE CONVERTING A SINGLE PHASE MACHINE TO THREE PHASE BE SURE

TO FOLLOW THE BOOSTER WIRING INSTRUCTIONS ON PAGES 71-72.

Refer to the connection diagrams below to connect main incoming power to the dishwasher.

lectrical Connections - UH330B with Built-in Booster

1PH and 3PH Wiring Diagrams

208-230

VAC

208-230

VAC

208-230 VAC

115VAC

GRD

THREE PHASE POWER CONNECTION

Models UH330B

HOW TO CONNECT 3 PHASE POWER

1. Check the data plate on the front of the

dishwasher for the phase of the machine.

2. Remove the lower access panel.

3. Pull power connection box forward and out.

4. The Main Terminal Block has terminals for

L1, L2, L3, Neutral and Ground.

5. Connect ground, then connect

L1, L2, L3 to 208-230VAC.

6. Connect a current carrying neutral to N.

7. Main power connections are complete.

If the data plate says the machine is 3 Phase,

then connect a 3 PH power supply.

! VERY IMPORTANT !

THE ELECTRICAL POWER MUST BE A

4-WIRE PLUS GROUND SUPPLY WHICH

INCLUDES A CURRENT CARRYING NEUTRAL.

208-230

VAC

0 VAC

115VAC

GRD

SINGLE PHASE POWER CONNECTION

Models UH330B

Do not connect power to L3

HOW TO CONNECT 1 PHASE POWER

! VERY IMPORTANT !

1. Check the data plate on the front of the

dishwasher for the phase of the machine.

2. Remove the lower access panel.

3. Pull power connection box forward and out.

4. The Main Terminal Block has connections

for L1, L2, L3, Neutral and Ground.

5. Connect ground, then connect

L1, L2 to 208-230VAC.

6. Connect a current carrying neutral to N.

7. Main Power connections are complete.

If the data plate says the machine is 1 Phase,

then connect a 1 PH power supply.

DO NOT CONNECT POWER TO L3.

THE ELECTRICAL POWER MUST BE A

3-WIRE PLUS GROUND SUPPLY WHICH

INCLUDES A CURRENT CARRYING NEUTRAL.

Summary of Contents for UH130 M4







































































































































































Search results

Summary of Contents for UH130 M4

Reviews:

Brands by name

Popular brands

Champion UH130 M4, Installation And Operation Manual

Search results

Summary of Contents for UH130 M4

Reviews:

Brands by name

Popular brands