manualshive.com logo in svg

Champion UH130 M4, Installation And Operation Manual

Share
Download
Champion UH130 M4 Installation And Operation Manual Download Page 47

37

Water Connection - 

UL130

1.  All models have a 6 ft. flexible hot water fill hose with a 3/4" female garden hose    

 connector.

2.  A 1/2" or larger main incoming supply line should be installed to the dishwasher. 
3.  We recommend that a 1/2" or larger shut-off valve be installed in the main water supply,  

 

as close to the dishwasher as possible for servicing.

4.  The UL130 has a built-in flow control which requires that the incoming hot water supply  

 

pressure must be between 25-95 psi. 

5.  The hot water supply must provide a minimum of 120°F/49°C, measured at the  

 

dishwasher; however, 140°F/60°C is recommended.

6.  A water hardness of 3 grains/gal (US) [51.3 mg/L] or less is recommended.  Hard 

 

water can adversely affect wash results.

1.  All models have a 6 ft.. 5/8" I.D. drain hose. The maximum drain height connection    

 

must not exceed  3 ft.[0.9 m]. 

2.  A 3/4" hose barb fitting is strapped to the drain hose to connect the drain hose to a  

 

wye drain fitting. The service part number for the hose barb is P/N 0512321.

3.  The maximum drain flow is 15 US gpm/12.4 imp gpm/60 lpm.  

Model UL130 - Installation 

Drain Connection - UL130

3/4" DRAIN HOSE BARB FITTING 

STRAPPED TO DRAIN HOSE

! VERY IMPORTANT !

 

Make sure that the flexible water supply and drain hoses are not kinked.  

Plumbing connections must allow the machine to be pulled out for service and cleaning.

Plumbing connections must comply with national, provincial local plumbing and sanitary codes. Only 

qualified service personnel familiar with food service equipment should install  

the machine. 

The installing plumber must thoroughly flush the water supply line to remove all debris  

BEFORE connecting the water supply line to the machine. 

DO NOT REMOVE HOSE 

CLAMPS 

NOR STRETCH HOSE 

Summary of Contents for UH130 M4







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands