manualshive.com logo in svg

Champion UH130 M4, Installation And Operation Manual

Share
Download
Champion UH130 M4 Installation And Operation Manual Download Page 96

86

Operation - 

Model UH330B

Drain Mode

The dishwasher will enter the drain mode whenever the ON-OFF/DRAIN power switch is pushed  

down to the OFF/DRAIN position.  The switch is located on the left side of the control panel.

IF THE ON-OFF/DRAIN SWITCH IS PLACED IN THE OFF/DRAIN POSITION FOR MORE 

THAN 3 SECONDS, THE DISHWASHER WILL CONTINUE TO DRAIN EVEN IF THE SWITCH 

IS PUSHED BACK TO THE ON POSITION.

1.  Remove any dish rack that may be inside the machine. 

2.  Push the illuminated power switch down to the OFF/DRAIN position.  

The power switch light will go out. 

3.  The cycle light will illuminate and the machine will drain. 

4.  The cycle light will go out indicating that the drain cycle is complete. 

DO NOT OPEN THE DOOR UNTIL THE LIGHT GOES OUT. 

POWER

START

OFF/DRAIN

ON

Operation - Model UH330B

! VERY IMPORTANT !

 

Draining Problems Related To Improper Installation.

 

Problems with machine draining are often the result of improper installation.   

NEVER EXTEND OR ADD LENGTH TO THE DRAIN HOSE.

Summary of Contents for UH130 M4







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands