manualshive.com logo in svg

Champion UH130 M4, Installation And Operation Manual

Share
Download
Champion UH130 M4 Installation And Operation Manual Download Page 31

21

Model UH130, UH130B, UH230, UH230B - Installation

Detergent and Rinse-aid Dispensing Pumps - Pump and Fill Adjustments  

UH130, UH130B and UH230, UH230B

To adjust the amount of chemicals dispensed 

by the pumps: 

1.  Make sure the chemical containers are full and  

 

the pick-up tubes are in their proper containers.

3.  Turn the dishwasher power switch ON.  

 

The switch will illuminate and the dishwasher  

 

will fill with water.

4.  Run a normal dishwasher cycle and test   

 

detergent and rinse-aid concentrations    

 

according to the chemical supplier's  

 

 instructions.

CAUTION:

 

Excessive pressure to the potentiometers when 

adjusting can result in bent or broken adjusting 

screws. 

5.  Each dispensing pump has a clearly marked  

 

adjustment screw.  Turn the screw CW to  

 

increase the run time of the dispensing pump  

 

and CCW to reduce the run time.

 

UH130, UH130B only  

To adjust the tank fill:  

1.  The fill adjustment screw will provide a   

 

small change in the tank water level.  

2.  If a large adjustment is needed, check the  

 

incoming  water pressure and make sure the fill  

 

hose is not kinked. 

3.  If the above items are okay then  the size  

 

of the incoming water supply should be   

 

checked. The incoming water supply line must  

 

be a minimum of 1/2" or larger. 

Refer to the photo below:

Fill Adjustment 

For UH130, UH130B 

Only

Use a 4mm 

blade  

screwdriver

Summary of Contents for UH130 M4







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands