manualshive.com logo in svg

Champion UH130 M4, Installation And Operation Manual

Share
Download
Champion UH130 M4 Installation And Operation Manual Download Page 102

92

Troubleshooting - UH330B

Troubleshooting - UH330B

Condition 

Cause 

Solution

Dishwasher will not run.

Low or no water.

Chemicals won’t feed into

dishwasher.

Door not closed.

Main power OFF.

Dishwasher OFF.

Circuit board fuse blown. 

Main water supply off.
Fill hose kinked.
Low incoming water pressure
Solenoid valve defective.
Solenoid strainer clogged.

Chemical supply low.
Supply tubing damaged.
Supply tubing kinked.
Pick-up tube clogged
Chemical circuit board fuse blown.
Pump squeeze tube defective. 

Close door completely.

Check breaker on panel.

Turn dishwasher power switch ON.

Contact service agent. 

Open supply valve.
Straighten fill hose.
Set flowing water pressure to 25-95 PSI.
Install repair kit or replace.
Clean strainer.

Refill chemical container.
Replace tubing.
Straighten tubing.
Clean/replace tube.
Contact service agent.
Replace squeeze tube.

Low water pressure

pumped from wash spray 

arms.

Clogged scrap screen.
Clogged spray arms.
Clogged pump intake.

Clean scrap screen.
Clean spray arms.
Inspect sump and clean pump intake.

Dishwasher stays in

wash cycle.

Rinse Sentry extends wash mode 

for a maximum time of 5-minutes 

to allow final rinse water booster 

temperature to reach 180˚F/82˚C.

Contact service agent.

Poor wash results.

Excessively hard water.
Thermistor defective.
(See chemicals won’t feed

 above.)
(See low or no water above.)
Detergent injector defective.

Chemical circuit board fuse blown.
Wares incorrectly loaded. 

in dishrack.

Booster high limit tripped.

Wash tank high limit tripped.
Rinse arm nozzles clogged.

Contact chemical supplier.
Replace thermistor.
(See chemicals won’t feed

above.)
(See low or no water above.)
Replace squeeze tube.

Replace injector motor.

Clean tubing and pick-up.
Contact service agent.
Reposition wares or reduce amount of 

wares in dish racks.

Reset or replace high limit.

Reset or replace high limit.
Clean nozzles with small paper clip.

Water has drained out of 

the wash tank while the 

dishwasher was idle.

Anti-siphoning loop in drain

hose has been removed.
Drain hose was extended.
Drain hose clamp is not

holding the drain hose 

in proper position.
Building plumbing does not

provide correct air vent

to prevent siphoning. 

Re-route drain hose.

DO NOT STRETCH HOSE
Replace/adjust hose clamp

making sure goose-neck

is maintained.
Contact service Agent

and/or plumber.

Summary of Contents for UH130 M4







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands