Champion UH130 M4 Installation And Operation Manual Download | Manualshive

Page: 38 / 166

background image

28

!

VERY IMPORTANT

!

DRAIN AND CLEAN THE DISHWASHER EVERY 2 HOURS OF CONTINUOUS

OPERATION, AFTER EACH MEAL PERIOD, AND AT THE END OF THE DAY.

All Models

!

ATTENTION

!

DO NOT USE METALLIC SCRUB PADS TO CLEAN THE MACHINE.

DO NOT SPRAY THE EXTERIOR OF THE MACHINE WITH WATER.

Cleaning - Model UH130, UH130B, UH230, UH230B

Cleaning - UH130, UH130B and UH230, UH230B

1. Remove the upper and lower spray arms and flush clean in a sink.
2. Remove the scrap screen taking care that debris does not fall off the screen and into the

wash tank or sump. Flush the screen clean in a sink. Be sure to back-flush the screen.

3.  DO NOT strike the scrap screen on solid surfaces.
4.  Check the sump for foreign material.
5.  Clean the pump intake strainer in the bottom of the sump.
6.  DO NOT scrub the interior with metal scrub pads.
7.  Check the sump heating element for lime deposits and gently remove with a scouring

pad. DO NOT USE METALLIC SCRUB PADS.

8. Wipe the exterior of the dishwasher with a soft clean cloth and a mild detergent.
9. Leave the door open to aid in overnight drying.

Cleaning the wash tank:

«
...
36
37
38
39
40
...
»

Summary of Contents for UH130 M4







































































































































































Reviews:

No comments

Related manuals for UH130 M4

3VT913NA - annexe 1

Brand: BALAY Pages: 25

3VT913NA - annexe 1

Brand: BALAY Pages: 30

Brand: BALAY Pages: 2

Brand: BALAY Pages: 2

Brand: BALAY Pages: 2

3VB350ID - annexe 1

Brand: BALAY Pages: 29

Brand: Haier Pages: 16

Brand: Heinner Pages: 86

Brand: Indesit Pages: 48

Brand: Akai Pages: 28

Brand: Baumatic Pages: 33

Brand: Hotpoint Ariston Pages: 76

Brand: Splendide Pages: 24

Brand: Solt Pages: 11

Brand: Gorenje Pages: 29

Brand: Maytag Pages: 27

Brand: FAVORIT Pages: 40

Brand: Hallman Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands