manualshive.com logo in svg

Champion UH130 M4, Installation And Operation Manual

Share
Download
Champion UH130 M4 Installation And Operation Manual Download Page 18

8

Installation - Model UH130, UH130B, UH230, UH230B

3.  Disconnect the existing booster heater wires and change the booster heater element 

 

jumpers as shown in the illustration below

4.  Connect wires 1H1, 1H2, and 1H3 as shown below. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.  A replacement 3PH data plate is stowed on the back of the lower front access panel.
6.  Replace the existing 1PH data plate on the front of the panel with the new 3PH data plate. 

 

Discard the 1PH data plate. 

7.  Refer to the instructions on page 3 to connect the main incoming power to the 

 machine.

1H1

1H2

1H3

Booster Heater

Connected for 1PH

1H1

Booster Heater

Connected for 3PH

1H2

1H3

Wire not

connected

Wiring Diagram - Booster heater element connections shown for 1 phase and 3 phase operation.

Booster Heater Conversion from 1PH to 3 PH Operation

 (continued)

! VERY IMPORTANT !

THE BOOSTER HEATER IS WIRED FOR 1PH OPERATION WHEN SHIPPED.

FOLLOW THE INSTRUCTIONS BELOW TO WIRE THE BOOSTER FOR 3PH.

Summary of Contents for UH130 M4







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands