manualshive.com logo in svg

Champion UH130 M4, Installation And Operation Manual

Share
Download
Champion UH130 M4 Installation And Operation Manual Download Page 11

1

NOTE:

The installation of your dishwasher must be performed by qualified service personnel familiar 

with food service equipment and must comply with all local health codes. 

Problems due to improper installation are not covered by the Limited Warranty.

NOTE:

The installation of the dishwasher must comply with all local electrical, plumbing, health and 

safety codes or in the absence of local codes, installed in accordance with the applicable  

requirements in the National Electrical Code, NFPA 70, Canadian Electrical Code (CEC),  

Part 1, CSA C22.1; and the Standard for Ventilation Control and Fire Protection of  

Commercial Cooking Operations, NFPA 96.

 

CAUTION:

Be careful when lifting and moving the dishwasher to prevent damage to the machine. 

1.  Inspect the outside of the dishwasher carton for signs of damage.
2.  Remove the carton and inspect the dishwasher for damage.
3.  Check for any options or accessories that may have shipped with your dishwasher.
4.  Compare the installation site utility connections with the dishwasher utility connections  

and make sure they are the same.  

5.  The dishwasher can be installed as a free-standing unit or under a counter-top. 

The typical counter-top height in most locations is 34" [86cm].

6.  It is highly recommended that the  

underside of the counter-top be clad 

in metal.

7.  Under counter installations should 

provide storage space for the 

dishwasher chemical supply 

containers. Do not elevate the 

containers above the finished floor.

8.  Chemical supply containers should 

be placed as close to the machine as 

possible and the chemical tubing 

taped to the back of the machine 

should be repositioned before 

permanently placing the machine.

9.  Place the dishwasher in its permanent 

location.

10.  The dishwasher has 4 adjustable feet 

for leveling.

11.  Level the dishwasher front-to-back and side-to-side.

Receiving and Placement - Installation

Receiving - UH130, UH130B, UH230, UH230B, UL130

Counter-top

Wall

3" 

[8cm]

 Min. 

34" 

[86cm]

Min.

Floor

Placement - UH130, UH130B, UH230, UH230B, UL130

Summary of Contents for UH130 M4







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands