manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 51

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

2-39 

2. Status Indicator RAPs

 

RAP 2.31 Face Jog Cylinder 

Output 6 

The face jog cylinder is a rotary cylinder used 
during the book registration process.  It jogs 
against the face of the book in order to keep the 
spine of the book firmly against the back of the 
gripper. 

Possible Fault Indicators 

 

The face jog fails to rotate into position. 

 

The gripper transport freezes in the reg-
istration area because the face jog fails 
to retract. 

Initial Actions 

Perform RAP 2.20 Pneumatic Pressure. 

Perform GP 6.14 Speed-Control Air Valves. 

Perform ADJ 4.22 Face Jog Pressure 

Clear all books from the machine.   

Check for air leaks and disconnected or pinched 
hoses. 

Check for loose or damaged wire 96 at the elec-
trical panel. 

Check that the cable connector on valve #11 is 
connected properly.  

Procedure 

1.  Switch the main air ON and main power ON. 

2.  Manually activate valve #11 by pressing the 

actuator button on the valve (Figure 2-47).  
Does the face jog cylinder rotate into posi-
tion? 

Y  N 

Disconnect power and replace valve #11 
(PL 5.22 Pneu. Manifold Asm. 59012-1). 

3.  Electrically activate valve #11 by shorting 

wire 96 to 74 at the main PWB.  Does the 
face jog cylinder rotate into position? 

Y  N 

Disconnect power and replace valve #11 
(PL 5.22 Pneu. Manifold Asm. 59012-1). 

4.  Disconnect power and replace the main 

PWB (REP 4.23 Main PWB Replacement). 

 

Figure 2-46. Face Jog Cylinder 

 

 

Figure 2-47. Pneumatic Valve #11 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands