manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 221

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

6-7 

6. General Procedures/Information

 

GP 6.6 Retro-reflective Sensors 

Retro-reflective sensors emit infrared beams 
that reflect back to the sensors by way of a re-
flector.   

The reflector should be mounted as parallel to 
the sensing surface as possible so that the re-
flected beam is sent directly back to the sensor. 

There are two types of retro-reflective sensors 
used in the trimmer and accessories: Side 
mount and thru-hole mount (Figure 6-8). 

Procedure 

1.  Switch the main power OFF. 

2.  Clean any debris from the sensor face, re-

flector, and the pathway in between. 

3.  Inspect the sensor and reflector for any 

physical damage.  Replace the sensor if the 
housing or body is cracked.  Replace the re-
flector if damaged or peeling. 

4.  Switch the main power ON.  Check the 

alignment of the sensor and reflector.  A red 
beam is emitted from the sensor that is visi-
ble on the reflector when aligned properly.  
Realign as necessary by adjusting the 
mounting brackets of the sensor and/or re-
flector. 

5. 

Click the “Diagnostic” button on the screen 
to bring up the diagnostic screen.  If applica-
ble, click on an accessory diagnostic button 
to bring up a specific accessory’s diagnostic 
screen. 

6.  Block the pathway between the sensor and 

reflector with a book or sheet of paper.  If 
the sensor and main PWB are working cor-
rectly, the LED on the sensor will change 
state, and an audible tone will be emitted 
from the main PWB.  Does the sensor 
change state each time the pathway is 
blocked and unblocked? 

Y  N 

a.  Re-check alignment 

b.  Perform the RAP associated with the 

specific sensor.   

Sensor adjustment complete. 

 

 

 

Figure 6-8. Retro-reflective Sensors 

 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands