manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 223

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

6-9 

6. General Procedures/Information

 

GP 6.8 Optical Distance Sensor 

The CMT-130TC uses an optical distance sen-
sor to determine the thickness of books just be-
fore they enter the gripper.  A red beam is emit-
ted from the sensor onto the conveyor belt, indi-
cating that the sensor is on.  The sensor can be 
recalibrated if necessary using the following pro-
cedure. 

Procedure 

1.  Switch the main power ON and press the 

“Setup” button to bring up the setup options. 

2. 

Press the “Service Info” tab to open the Ser-
vice Info screen.  Click on the “Enable Tabs 
Code” text box, enter in the code 

6125

 and 

press enter.  This will unlock all of the locked 
tabs. 

3. 

Press the “Accuracy Adjust” tab to open the 
Accuracy Adjust screen. 

4. 

Click on the “Thickness Sensor” button 

5.  Follow the instructions on the screen to re-

calibrate the sensor.  Exit the setup screen 
when finished. 

6.  Perform RAP 2.49 Book Thickness Sensor 

to make sure the sensor is functioning 
properly. 

 

 

Figure 6-10. Optical Distance Sensor 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands