manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 266

 

 

 

MAY 2019 

 

8. Installation

 

8-6 

CMT-130TC Book Trimmer 

Infeed Option 2: 
Tilt Conv. + El Pile Feeder 

 

Figure 8-15. Infeed Conv. + El Pile 

Feeder 

Setup Procedure 

1.  Perform installation steps 1 through 8 for In-

feed Option 1, Tilt Co Elevator. 

2.  Setup the book pile feeder according to the 

instruction and parts manual supplied with 
the book pile feeder. 

3.  Attach the pile feeder to the elevator. 

4.  Move the trimmer into position against the 

pile feeder, aligning the mounting brackets 
on the pile feeder to the corresponding holes 
in the side of the trimmer.  Once the trimmer 
height is set properly according to Section 
8.5 Trimmer Height Setup, attach the pile 
feeder to the trimmer using supplied mount-
ing hardware. 

Cable and Air Tubing Connections

 

1.  Remove the lower front panel of the trimmer 

and locate the yellow power cable coiled up 
inside the trimmer that is labelled with the 
number that corresponds to the label on the 
elevator near the input connectors.  The 

power cables are the larger diameter cables 
with 7-pin connectors on the end.   

2.  Route the power cable under the hydraulic 

unit and out of the left side of the trimmer. 

3.  Connect the power cables as shown in Fig-

ure 8-16. 

 

 

Figure 8-16. Power Cable Connections 

4.  Now locate the yellow communication cable 

coiled up inside the trimmer that is labelled 
with the number that corresponds to the la-
bel on the elevator near the input connect-
ors.  It is a small diameter cable with a 3-pin 
connector on the end.  Also locate any sepa-
rate communication cables that were sup-
plied with the infeed/outfeed options. 

5.  Connect the communication cables as 

shown in Figure 8-17. 

 

 

Figure 8-17. Comm. Cable Connections 

6.  Now locate the coiled-up line of blue air tub-

ing with a red and white connector on the 
end that is labelled with the numbers that 
correspond to the labels on the pile feeder, 
elevator, and tilt conveyor near the input 
connectors.  Also locate any separate air 
tubing sections that may have been supplied 
with the infeed/outfeed options. 

7.  Connect the air tubing as shown in Figure 

8-18.  

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands