Challenge 130TC-A-160000 Service Manual Download Page 106

Page: 106 / 282

MAY 2019

3. Book Quality

3-6

CMT-130TC Book Trimmer

BQ 3.10 Books Not Accurately
Trimmed

Description

Books are not being trimmed to the dimensions
or locations that are intended.

Possible Causes



The trimmer’s accuracy is not set cor-
rectly.



Books are not registering in the registra-
tion area properly, causing the books to
be misaligned in the gripper when being
trimmed.

Solutions



Recalibrate the machine’s accuracy set-
tings (ADJ 4.5 Accuracy Adjustment).



Check function of left side jogging cylin-
der (ADJ 4.20 Left Jog Pressure Adjust-
ment and RAP 2.21 Left Jogger Cylin-
der).



Check function of face jogger (RAP 2.31
Face Jog Cylinder and ADJ 4.22 Face
Jog Pressure).



Check function of the registration plate
extend cylinder (RAP 2.26 Registration
Plate Extend Cylinder).



Check function of the gripper clamp
(ADJ 4.21 Gripper Clamp Pressure).

Summary of Contents for 130TC-A-160000



























































































































































































































































































Search results

Summary of Contents for 130TC-A-160000

Reviews:

Brands by name

Popular brands

Challenge 130TC-A-160000, Service Manual

Search results

Summary of Contents for 130TC-A-160000

Reviews:

Brands by name

Popular brands