manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 45

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

2-33 

2. Status Indicator RAPs

 

RAP 2.25 Gripper Lift Cylinder 

Output 28 

The gripper lift cylinder lifts the entire gripper as-
sembly up and down (Figure 2-34).  The cylinder 
extends whenever the gripper is in motion, thus 
lifting the book slightly above the table surface 
whenever it is in motion. 

Possible Fault Indicators 

 

Books have nicks or scuff marks on bot-
tom cover, especially near the spine. 

Initial Actions 

Perform RAP 2.20 Pneumatic Pressure. 

Perform GP 6.14 Speed-Control Air Valves. 

Check for air leaks and disconnected or pinched 
hoses. 

Check for loose or damaged wire 69 at the elec-
trical panel. 

Check that the cable connector on valve #6 is 
connected properly.  

Procedure 

1.  Switch the main air ON and main power ON. 

2.  Manually activate valve #6 by pressing the 

actuator button on the valve (Figure 2-35).  
Does the valve activate? 

Y  N 

Disconnect power and replace valve #6 (PL 
5.22 Pneu. Manifold Asm. 59012-1). 

3.  Electrically activate valve #6 by shorting wire 

69 to 74 at the main PWB.  Does the valve 
activate? 

Y  N 

Disconnect power and replace valve #6 (PL 
5.22 Pneu. Manifold Asm. 59012-1). 

4.  Disconnect power and replace the main 

PWB (REP 4.23 Main PWB Replacement). 

 

 

Figure 2-34. Gripper Lift Cylinder 

 

 

Figure 2-35. Pneumatic Valve #6 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands