manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 83

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

2-71 

2. Status Indicator RAPs

 

RAP 2.63 Elevator Empty Sensor 

Elevator I/O PWB Input 10 

The Elevator empty sensor (Figure 2-98) is a 
retro-reflective sensor that detects if there are 
any books in the Elevator that need to be lifted 
and fed into the trimmer.  The reflector is located 
on the bottom side of the pusher arm. 

Possible Fault Indicators 

 

The Elevat

or doesn’t lift when there are 

books in it. 

 

The Elevator lifts multiple times without 
any books in it. 

Initial Actions 

Check that all cables between the trimmer, Ele-
vator, and Tilt Infeed Conveyor are securely fas-
tened and are not damaged. 

Check that the reflector is in place (Figure 2-98). 
Replace if necessary (PL 5.29 Elevator 
56421TCA (2/7)). 

Check and repair loose or damaged wires 47, 
73, and 74 at the Elevator electrical panel. 

Procedure 

1.  Switch the main power ON and go to the El-

evator diagnostic screen (GP 6.2 Input/Out-
put Diagnostics).  Make sure that the sensor 
is not obstructed.  Is input “Elevator Empty” 
off? 

Y  N 

Disconnect wire 47.  On the diagnostic 
screen does input “Elevator Empty” switch 
off? 

Y  N 

Disconnect power and replace the Ele-
vator I/O PWB (REP 4.26 Accessory 
PWB Replacement). 

Adjust the sensor (GP 6.6 Retro-reflective 
Sensors) and replace if faulty (PL 5.28 Ele-
vator 56421TCA (1/7) or PL 5.37 Elev. Elec-
trical Panel EE-3523). 

2.  Short wire 47 to 74.  On the diagnostic 

screen does input “Elevator Empty” switch 
on? 

Y  N 

Disconnect power and replace the Elevator 
I/O PWB (REP 4.26 Accessory PWB Re-
placement). 

3.  Adjust the sensor (GP 6.6 Retro-reflective 

Sensors) and replace if faulty (PL 5.28 Ele-
vator 56421TCA (1/7) or PL 5.37 Elev. Elec-
trical Panel EE-3523). 

 

 

Figure 2-98. Elevator Empty Sensor 

 

Figure 2-99. Elevator Electrical Panel 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands