Cerio DT-300N User Manual Download Page 97

 

 

 

Disable

 : Data are unencrypted during transmission when this option is selected.

 

 

WEP

 : Wired Equivalent Privacy(WEP) is a data encryption mechanism based on a 64-bit 

or 128-bit shared key.

 

 

 

Key Index

 : Skey index is used to designate the WEP key during data transmission. 

4 different WEP keys can be entered at the same time, but only one is chosen.

 

 

Key Auth Method :

 Enable the desire option among OPEN or SHARED .

 

 

WEP Key #

 : Enter HEX or ASCII format WEP key value; the system supports up to 

4 sets of WEP keys.

 

Key Length 

Hex 

ASCII 

64-bit 

10 characters 

5 characters 

128-bit 

26 characters 

13 characters 

 

 

WPA-PSK (or WPA2-PSK) : 

WPA (or WPA2) Algorithms, allows the system accessing the network by using the WPA-PSK 

protected access. 

 

 

Cipher Suite

 : By default, it is AES. Select either AES or TKIP cipher suites.

 

 

Pre-shared Key

 : Enter the pre-shared key; the format shall go with the selected key 

type.

 

 

 

 

 

 

Pre-shared key can be entered with either a 256-bit secret in 64 HEX digits format, or 

8 to 63 ASCII characters. 

Summary of Contents for DT-300N





































































































































































Reviews: