manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 101

 

 

6.  WISP + AP Mode Configuration

 

When WISP + AP Mode is chosen, the system can be configured as an WISP + AP Mode. This section 

provides detailed explanation for users to configure in the WISP + AP Mode with help of illustrations. In 

the WISP + AP Mode, functions listed in the table below are also available from the Web-based GUI 

interface. 

6.1   Chose Your Operating Mode ( WISP + Repeater AP Mode ) 

The system administrator can set the desired mode via this page, and then configure the system 

according to their deployment needs, Please click on System -> Operating Mode and follow the 

below setting. 

 

 

 

 

 

6.2 External Network Connection ( Network Requirement ) 

It can be used as an Outdoor Customer Premises Equipment (WISP) to receive wireless signal 

over last mile application, helping WISPs deliver wireless broadband Internet service to residents 

and business customers. In the WISP mode, 

DT-300N

 is a gateway enabled with NAT and DHCP 

Server functions. The wired clients connected to 

DT-300N

 are in 

different

 subnet from those 

connected to Main Base Station, and, in WISP mode, it 

does not 

accept wireless association from 

wireless clients. 

 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands