manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 148

 

 

network to the destination host. The test is started using the 

Start

 button, click 

Stop

 button to 

stopped test. 

 

Destination Host

 : Specifies the Destination Host for the finding the route taken by 

ICMP packets across the network. 

 

MAX Hop

 : Specifies the maximum number of hops( max time-to-live value) trace route 

will probe. 

 

 

 

 

 

 

 

 

9.4   PoE Bridge 

CERIO DT-300N 

Design smart PoE Bridge function, the PoE Bridge function support provide next 

AP power. Can will be structure become very convenience. And the PoE bridge support CERIO 

WM-series AP or OW-series to be dual band budle wireless soultion.(

 

The hardware Install can 

reference to “1.6 Hardware Installation Steps”) 

 

 

Service : 

The default is Disable, the function can Enable or Disable PoE Power

 

 

 

 

9.5 Reboot 

This function allows user to restart system with existing or most current settings when changes are 

made. Click 

Reboot

 button to proceed and take around three minutes to complete. 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands