manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 51

 

 

 

 

Hostname

 : The Hostname of the LAN port. 

 

 

DNS

: Check either “

No Default DNS Server

” or “

Specify DNS Server IP

” button as desired 

to set up the system DNS. 

 

Primary

 : The IP address of the primary DNS server. 

 

Secondary

 : The IP address of the secondary DNS server. 

 

 

802.1d Spanning Tree

 

The spanning tree network protocol provides a loop free topology for a bridged LAN between 

LAN interface and 8 WDS interfaces from wds0 to wds7. The Spanning Tree Protocol, which 

is also referred to as STP, is defined in the IEEE Standard 802.1d 

 

 

Click 

Save

 button to save your changes. Then click 

Reboot

 button to activate your changes. 

 

3.4   Wireless 

General Setup

 

The administrator can change the data transmission, channel and output power settings for the 

system. Please click on 

Wireless -> General Setup

 and follow the below setting. 

 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands