manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 65

 

 

Authentication RADIUS Server Settings

 

 

 

Authentication Server

: Enter the IP address of the Authentication RADIUS 

server. 

 

Port

: The port number used by Authentication RADIUS server. Use the default 

1812 or enter port number specified. 

 

Shared secret

: The secret key for system to communicate with Authentication 

RADIUS server. Support 1 to 64 characters. 

 

Accounting Server

: Check on the respected button to enable either Enable or 

Disable accounting RADIUS server. 

 

Secondary Authentication RADIUS Server

 

 

 

Authentication Server

: Enter the IP address of the Authentication RADIUS 

server. 

 

Port

: The port number used by Authentication RADIUS server. Use the default 

1812 or enter port number specified. 

 

Shared secret

: The secret key for system to communicate with Authentication 

RADIUS server. Support 1 to 64 characters. 

 

 

WEP 802.1x : 

When WEP 802.1x Authentication is enabled, please refer to the 

following Dynamic WEP and RADIUS settings to complete the configuration. 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands