manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 107

 

 

 

 

 

 

 

Manual MAC Address :

 Enter the MAC address registered with your ISP. 

 

 

Click 

Save

 button to save your changes. Click 

Reboot

 button to activate your changes 

 

 

 

 

6.4 Configure DT-300N LAN IP Address 

Here are the instructions for how to setup the local IP Address and Netmask. Please click on 

System -> LAN

 and follow the below setting. 

 

 

LAN IP Setup : 

The administrator can manually setup the LAN IP address. 

 

IP Address :

 The IP address of the LAN port; default IP address is 192.168.2.254 

 

IP Netmask :

 The Subnet mask of the LAN port; default Netmask is 255.255.255.0 

 

 

802.1d Spanning Tree : 

The spanning tree network protocol provides a loop free topology for a bridged LAN 

between LAN interface and 8 WDS interfaces from wds0 to wds7. The Spanning Tree 

Protocol, which is also referred to as STP, is defined in the IEEE Standard 802.1d. 

 

The Clone MAC Address field will display MAC address of the PC 

connected to system. Click “Save” button can make clone MAC 

effective. 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands