manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 29

 

 

 

Hostname:

 Host Name that you register to Dynamic-DNS service and export. 

 

User Name & Password:

 User Name and Password are used to login DDNS service. 

 

Click 

Save

 button to save your changes. Click 

Reboot

 button to activate your changes 

 

2.4 Configure DT-300N LAN IP Address

 

Here are the instructions for how to setup the local IP Address and Netmask. Please click on 

System -> LAN

 and follow the below setting. 

 

 

LAN IP Setup : 

The administrator can manually setup the LAN IP address. 

 

IP Address :

 The IP address of the LAN port; default IP address is 192.168.2.254 

 

IP Netmask :

 The Subnet mask of the LAN port; default Netmask is 255.255.255.0 

 

 

802.1d Spanning Tree : 

The spanning tree network protocol provides a loop free topology for a bridged LAN 

between LAN interface and 8 WDS interfaces from wds0 to wds7. The Spanning Tree 

Protocol, which is also referred to as STP, is defined in the IEEE Standard 802.1d. 

 

 

 

 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands