manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 103

 

 

 

 

Mode :

 By default, it’s “

Static IP

”. Check “Static IP”, “Dynamic IP”, “PPPoE” or “PPTP”to 

set up system WAN IP 

 

Static IP : 

Users can manually setup the WAN IP address with a static IP provided 

by WISP. 

 

IP Address :

 The IP address of the WAN port; default IP address is 192.168.1.254 

 

IP Netmask :

 The Subnet mask of the WAN port; default Netmask is 255.255.255.0 

 

IP Gateway :

 The default gateway of the WAN port; default Gateway is 192.168.1.1 

 

 

Dynamic IP :

 Please consult with WISP for correct wireless settings to associate 

with WISP AP before a dynamic IP, along with related IP settings including DNS can 

be available from DHCP server. If IP Address is not assigned, please double check 

with your wireless settings and ensure successful association.    Also, you may go to   

“

WAN

 

Information

” in the Overview page to click 

Release

 button to release IP 

address and click 

Renew

 button to renew IP address again. 

 

 

Hostname :

 The Hostname of the WAN port 

 

 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands