manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 81

 

 

 

VLAN Tag(ID)

: Virtual LAN, the system supports tagged VLAN with WDS. To enable 

VLAN function; valid values are from 0 to 4094; space is disabled. 

 

Description 

: Description of WDS link. 

 

 

Notice: The WDS link needs to be set at same Channel and with same 

Security Type. 

 

Click 

Save

 button to save your changes. Click 

Reboot

 button to activate your changes. 

 

 

4.7   WDS Status 

The Peers MAC Address, antenna 0/1 received signal strength, phy mode and channel bandwidth 

for each WDS are available. 

 

 

MAC Address :

 Display MAC address of WDS peer.

 

 

RSSI : 

Indicate the RSSI of the respective WDS's link.

 

 

TX/RX Rate :

 Indicate the TX/RX Rate of the respective WDS's link

 

 

TX/RX SEQ :

 Indicate the TX/RX sequence of the respective WDS's link

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands