manualshive.com logo in svg

CBE 520, Safety, Installation, Operation, Maintenance

Share
Download
CBE 520 Safety, Installation, Operation, Maintenance Download Page 59

 

 

59 

 

 

 

 

 

 

Name of the levels and timers 

1-

Choice Bagging Equipment (CBE )

 

2-

Bag Pre-Inflate 

3-

Vibrator / Densifier On-Delay 

4

. Slide gate / Feed gate filler head  

5-

Input / Output Screen illuminations

 

 

 

 

Adjusting the Timer: 

 

Use the 

A

 

or 

B

 

button to Scroll forward or backward through the Timers. 

 

 

 

When you reach the desired timer press the OK  key. (The timer is able to be edited when 
the selected time flashes with solid blocks.  The timer is not editable when the selected 
timer flashes the time only.) 

Use the

 

+ 

and

 

– 

keys to adjust the timer up and down in 0.1 second increments.

 

When done press the OK key again and timers will flash not as a block but more individual. 

Press the Escape key to return to menu and using the up/ down arrows scroll back to the 
CBE screen.  

  

 

 

 

Summary of Contents for 520






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands