manualshive.com logo in svg

CBE 520, Safety, Installation, Operation, Maintenance

Share
Download
CBE 520 Safety, Installation, Operation, Maintenance Download Page 24

 

 

24 

 

 

 

The CBE 520 Bulk Bag Filler is comprised of the following assemblies

: 

 
1.  Digital Filler 
Controller (104-1050) 

The digital filler controller controls all aspects of the bag filling cycle.  It is directly 
responsible  for  controlling  the  solenoid  valves  and  cylinder  operated  functions  of 
the machine. 
 

2.  Solenoid/ Pneumatic 
Assembly (CBE-105----) 
 
NOTE:  App Specific 

The  solenoids  or  pneumatic  valve  control  the  air  operated  functions  of  the 
machine.    A  configuration  of  three  to  six  solenoid  are  located  in  the  typical 
solenoid control panel. 
 

3.  Start / Stop / E-Stop 
Push Button Control 
Station (115-900) 

Allows for Manual Start, Stop, Pause and Emergency Shut Down of the Machine.  
 
 

4.  

Dust Tight 12” Fill 

Head w/ Slide-Gate Inlet 
(CBE-502----) 
 
NOTE App Specific 

12”  ID  Bulk  Bag  Fill  Head  with  Inflatable  Bag  Seal  Cuff  Designed  to  Inflate  and 
Seal  Against  the  Inside  of  the  Bulk  Bag  Neck  to  Prevent  Displaced  Air  from 
Escaping the Bag During the Bag Filling Process.  A Slide-Gate Valve Starts and 
Stops the Flow of Product into the Bag. 
 

5.  Bag Strap Release 
Assembly (501-700) 

Set  of  Four  (4)  Pneumatically  Operated  Latches  that  Hold  the  Bag  Straps  of  the 
Bulk  Bag  During  the  Filling  Process.    At  the  End  of  Each  Bag  Fill,  the  Strap 
Releases  will  Automatically  Release  Freeing  the  Bag  so  that  the  Bag  can  be 
Removed and the Filling Process Started Again.  
 

6.  Motor Control 
Assembly (CBE 509----) 
 
NOTE:  App Specific) 
 

Motor Controls to Operate Conveyor & Other Motorized Functions of the Machine 
Including:    Pre-Fill  Bag  Inflator,  Vibratory  Bag  Settler,  Discharge  Conveyor  and 
Powered  Accumulator  Conveyors.  (Controls  Wired  for  Either  220  or  440  Volt  /  3 
Phase / 60 Cycle) 
 

7.  Live Roller Bag 
Discharge Conveyor 
(512-100) 

A  trigger  switch  that  is  integrated  underneath  the  filling  spout  that  automatically 
initiates the bag fill upon the placement of empty bags onto the filling spout saving 
the  operator  from  manually  pressing  the  start  button  to  start  the  during  fill.    This 
device is an excellent time saver. 
 

8.  Pop-Up Grid Deck 
Vibratory Densifier (513-
300) 

Vibratory  Densifying  Grid  Table  Designed  to  Lift  a  Pallet  Off  of  a  Live  Roller 
Conveyor,  Settle  or  Densify  Product  in  the  Bag  or  Box  without  Vibrating  the 
Conveyor and Lowering the Pallet Back Onto the Live Roller Conveyor So It Can 
Be Automatically Exited from the System After Densifying.  Grid Deck Elevation is 
Accomplished  Via  (4)  Air  Mounts.    Controls  Wired  for  Either  220  /  440  Volt  /  3 
Phase / 60 Cycle) 
 

9. Rigid Mount Bag 
Densifier Assembly 
(Cushion Mounts w /Dual 
Vibratory Motors(513-
1000   

Vibratory  Densifying  Rigid  Deck  Mount  Designed  with  dual  motor  vibrators 
mounted on each side of the deck to Settle and/or Densify Product in Bulk Bag or 
Box.  Controls wired for either 220 / 440 Volt / 3 Phase / 60 Cycle)                                         
 
 
 
 

9.  10’ Gravity Roller 
Accumulation Conveyor 
(515-100) 
 

10’  Long  X  54”  Wide  Gravity  Roller  Conveyor  Designed  to  Receive  Filled  Bags 
from the 512-100 Bag Discharge Conveyor so that a the Bag Filler can be Reset 
for the Next Bag and Not be Tied Up Waiting on a Forklift. 
 

Summary of Contents for 520






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands