Cardin 100/SL324EBSB, Instruction Manual

Page: 16 / 52

16
SCALA: 1:2
Prodotti Technocity
SL324
14-02-2005
DI0361
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Sblocco carter
A
- The geared motor unit has been assembled in the fac-
tory to be fitted to the
LEFT SIDE
of the gate (internal
view). To install the motor to the RIGHT of the gate
set dip
8
OFTHEDIPSWITCH
DS1
lG TO
ON
Manual release is to be carried out with the motor stopped. To release the gate
use the manual release key supplied with the unit. The key should be kept in
an easily accessible place.
To release the unit
1. Rotate the lock protection disk, insert the key,
rotate it half a turn anticlockwise and lift up the
knob cover.
The knob is now free and can be released.
2. Rotate the knob clockwise until it can turn no more.
Attention
: do not force the knob to turn further
than its travel limit. The gears are now released
and the gate can be moved manually.
To relock the unit
1. Rotate the knob anticlockwise and move it back to the blocked position.
2. Close the knob cover, rotate the key clockwise and rotate the lock pro-
tection disk cover.
The gears are now blocked and the gate is ready for use. Once the
system has been reset store the key in a safe place.
Attention!
Never use the manual release mechanism while
the gate is in operation. If you release the gate and then give a
movement command the following symbol will appear on the
display .
Access to the electronic card
Attention!
Before opening the cover make sure
that the power has been switched off at the
mains.
4OACCESSTHEMOTORLOOSENTHETWOSCREWS A
positioned on either end of the cover as indicated
in figure 9.
Electronic programmer for a dc motor with an incorporated radio receiver card,
which allows the memorisation of 300 user codes SEEREMOTECONTROLPAGE
4HEROLLINGCODETYPEDECODERUSES
433.92 MHz
series transmitters.
The motor rotation speed is electronically controlled, starting slowly and
increasing in speed; the speed is reduced as it nears the travel limit so as to
enable a controlled smooth stop.
Programming is carried out using one button and allows you to set the system,
the current sensor and the entire gate travel distance.
The logic carries out position control using an encoder.
The intervention of the anticrush/antidrag sensor during the closing and opening
stages causes a brief ( 10 cm ) travel direction inversion then a block.
s !FTERHAVINGINSTALLEDTHEDEVICEAND before powering up the
programmer
, release the gate (manual release mechanism) and
move it manually, checking that it moves smoothly and has no
unusual points of resistance.
s 4HEPROGRAMMERCANACTIVATETHEMOTORAUTOMATICALLY4HISIS
indicated by the warning lights pre-flashing for 10 seconds, and by
the symbol
APPEARINGONTHEDISPLAY automatic reposition-
ing
ONPAGE
s 4HE PROGRAMMER IS lTTED WITH AN ELECTRICAL INPUT MONITORING
system, which is used to block the motor in emergency conditions;
however this system is not active during the following stages:
- during the first 5 s of an opening stage starting from completely
closed
- during the first 2 seconds of all other movement stages
- when the battery undercharged
Do not therefore attempt to physically block the door during these
stages, otherwise you may risk blowing the motor circuit protec-
TIONFUSE F1
s )FYOUNEEDTOCHECKTHESTATUSOFTHEFUSE F2 DISCONNECTTHE
power supply to the programmer; reconnect it only after having
re-inserted the fuse.
s
The presence of the electrical input monitoring system does
not exclude the need to install photoelectric cells or other safety
devices which are foreseen by the local standards and regulations
in force
.
s The geared motor unit has been assembled in the factory to be
lTTEDTOTHELEFTSIDEOFTHEGATE2EADTHEPARAGRAPH instructions
for positioning the unit
s For the correct operation of the programmer the incorporated
batteries must be in good condition: the programmer will lose the
position of the gate in case of blackouts when the batteries are flat,
the alarm will sound and automatic repositioning will take place .
Check the good working order of the batteries every six months
SEEPAGE
Battery check
s "EFORECONNECTINGTHEAPPLIANCEMAKESURETHATTHEVOLTAGEAND
frequency rated on the data plate conform to those of the mains
supply.
s !NALLPOLETRIPSWITCHWITHATLEAST 3 mm between the contacts
must be installed between the unit and the mains supply.
s $ONgTUSECABLESWITHALUMINIUMCONDUCTORSDONgTSOLDERTHE
ends of cables which are to be inserted into the binding posts; use
cables marked
T min 85°C
and resistant to atmospheric agents.
s 4HETERMINALWIRESMUSTBEPOSITIONEDINSUCHAWAYTHATBOTH
the wire and the insulating sheath are tightly fastened (a plastic
jubilee clip is sufficient).
Mains power supply connection
s #ONNECTTHECONTROLANDSECURITYDEVICEWIRES
s 2UNTHEMAINSPOWERSUPPLYTHROUGHTHECABLECLAMPLOCATEDONTHEBOTTOM
right of the main circuit board and to the separate 3-way terminal board:
- connect the neutral to binding post N
- connect the earth to binding post
- connect the live to binding post L
INSTRUCTIONS FOR POSITIONING THE UNIT
SCALA: 1:2
Pr
odotti T
echnocity
SL324
14-02-2005
DI0365
Description :
Pr
oduct Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San V
endemiano (TV) Italy - via Raf
faello, 36 T
el: 0438/401818 Fax: 0438/401831
Draft :
All rights r
eserved. Unauthorised copying or use of the information contained in this document is punishable by law
VIS
TA
IN
TE
R
N
A
C
A
N
C
E
LL
O
S
L1
52
4
7
MANUAL MANOEUVRE WITH THE MOTOR RELEASED
ELECTRONIC PROGRAMMER
1 2 3 4 5 6 7 8 9
ON
SCALA: 1:2
Prodotti Technocity
SL324
07-02-2002
DI0363
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Sblocco motore
8
9
IMPORTANT REMARKS
N
L
Fissaggio placca inferiore
06-03-95
DI0286
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Collegamento motore