![background image](http://html1.mh-extra.com/html/cardin/100-sl324ebsb/100-sl324ebsb_instruction-manual_2555953015.webp)
15
If the runner guide already exists the cement base should be extended
to take in part of the runner guide foundation.
This will stop the two foundations from giving way separately.
- Unscrew the four M12 nuts on the four threaded bolts (previously
used to block the anchor bolts) from the base of the anchor
plate. Then insert the four washers and allow them to rest on
the nuts.
- Position the geared motor over the four threaded bolts and
allow it to rest on the four washers.
- Fasten in to the base using the other
four washers and adjustment nuts
supplied with the kit, making sure
that the unit remains perfectly level
and stable.
- Adjust the height if the unit
using the four grub screws
already positioned on the
motor.
This will allow you to adjust
the height and position of
the motor later on.
- check the gate components, replace any worn or damaged parts and then
lubricate them.
USINGASPIRITLEVEL
N
CHECKTHATTHECASTORGUIDEISINSQUARE
THEUPPERRUNNERGUIDE
O
MUSTHAVETHECORRECTPLAYFORTHEGATEANDMUST
not inhibit the gate’s sliding action.
- check that a mechanical travel limit
Q
(absolutely necessary) has been
fitted in the opening direction and that it corresponds to the maximum travel
DISTANCE
P
OFTHEGATE
The travel limit must guarantee anti-derailment and gate stability.
Warning!
It is the installer’s responsibility to check all critical danger
points, to take action and to install any devices needed to guarantee
the safety of all people using the gate (risk analysis).
Important:
The geared motor can be positioned either to the left or to the
right of the passageway.
2EADTHEPARAGRAPH
INSTRUCTIONS FOR POSITIONING THE UNIT
/NCE
the correct position has been chosen proceed as follows:
Anchoring the unit
(fig. 4, 5, 6)
Important!
Check the exact anchoring position with respect to the alignment
of the sliding gate.
s 2UNTHEPIPINGANDCONNECTIONWIRESTOTHEPOSITIONWHERETHEMOTORISTO
be installed.
s !TTACHTHEANCHORBOLTSTOTHEBASEPLATE
A
ALLOWINGTHEMTOPROTRUDEBY
50 mm
and then tighten down using the supplied
M12
nuts.
s 0REPAREACEMENTPLINTHINTHEPOSITIONWHERETHEMOTORISTOBEINSTALLED
with a depth of
350 mm
(the base should protrude by about
25 mm
to avoid
damage by pools of water building up under the appliance).
s )NSERTTHEBASEPLATEMAKINGSURETHAT
THEELECTRICALCABLESPASSTHROUGHTHEHOLE
B
THEANCHORBOLTS
C
AREIMMERSEDINTOTHECEMENTBASEANDTHEBASEPLATE
is perfectly level;
- the four protruding (
50 mm
) threaded bolts are perpendicular to the base
plate;
- the surface area of the base plate is clean and free of cement residue.
SCALA: 1:2
Prodotti Cardin
SL1524
03-05-2005
DI0406
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
VISTA DI FIANCO SENZA MOTORE
con plinto 350 mm
25
110
104,5
50
325
5
INSTALLATION INSTRUCTIONS
Fitting the toothed rack
- release the geared motor (fig. 8), lay the first stretch of the toothed
rack on the pinion and fix it to the gate, then fasten down all the other
parts along the entire length of the gate.
- after having fastened the toothed rack, realign the pinion (play of
1
to 2 mm
between the toothed runner and the pinion) using the grub
screws at the base of the geared motor.
This action will prevent the weight of the sliding gate from damaging
the unit when working.
SCALA: 1:2
Prodotti Technocity
SL1524
08-02-2002
DI0240
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
VISTA DI FIANCO CON MOTORE
25
15
2 mm
325
SCALA: 1:2
Prodotti Technocity
SL1524
06-02-2002
DI0238
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
VISTA CONTROPIASTRA SL1524
69
4
3
2
1
34
SCALA: 1:2
Prodotti Technocity
SL1524M
30-01-2002
DI0237
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
CONTROPIASTRA SL1524M
M12
50 mm
312
31
54
34
157
69
43
A
B
C
4
6
Summary of Contents for 100/SL324EBSB
Page 50: ...NOTES 50...