Canon imageRUNNER C1325 Series, Service Manual

Page: 524 / 607

8
8
8-85
8-85
Service Mode > COPIER > OPTION > FNC-SW
Service Mode > COPIER > OPTION > FNC-SW
COPIER> OPTION> FNC-SW
DMAX-SW Setting of D-max control timing
Details To set the D-max control execution timing.
When the density variation is not within the requested range at
continuous output of a large volume of papers (long job length), set
2. When keeping the productivity even though there are some density
variations, set 1.
Use case • When the density variation is not within the requested range at
continuous output of a large volume of papers
• When keeping the productivity even though there are some density
variations
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range
0 to 2
0: Not used, 1: At last rotation
2: At paper interval with 1/1 speed and last rotation
Default value 2
BK-4CSW Set simple full clr mode: hvy ppr, Bk-m
Details To set the conditions to switch single Bk-color mode to simple full color
mode according to the type of heavy paper.
In single Bk-color mode, shock image at 75/122 mm from the leading
edge is likely to occur due to impact triggered by paper entering the
secondary transfer section.
By switching to simple full color mode where black is made by using
small amount of Y, M and C toners, shock image is alleviated.
When 0 (normal) is set, the mode is switched to simple full color mode
with heavy paper 3 after printing the specified number of sheets since
the replacement of the Drum Unit (Bk).
When 1, 2, or 3 is set, simple full color mode is always applied to heavy
paper 1/2/3.
When 4 is set, it is not switched to simple full color mode.
Use case When shock image occurs with heavy paper at single Bk-color mode
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 4
0: Normal
1: Heavy paper 3
2: Heavy paper 2/3
3: Heavy paper 1/2/3
4: OFF
Default value 0
COPIER> OPTION> FNC-SW
FXWRNLVL Set Fix Film life display threshold VL
Details To set the threshold value to display the life of Fixing Film.
This item is enabled when the value at the following is set to “1” (default:
0): COPIER> OPTION> DSPLY-SW> FXMSG-SW (ON/OFF of Fixing
Assembly replacement message)
The life judgment counter is stored in the DC Controller. It is not possible
to change or check the counter value.
Use case When preventing the occurrence of fixing failure caused by the
continuous use of the Fixing Film beyond its life
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 3
0: Warning is hidden.
1: Warning is displayed when the life counter reaches the specified
value.
2. Warning is displayed when the print counter reaches the specified
value.
3: Warning is displayed when either the life counter or the print counter
reaches the specified value.
Default value 0
Related service mode COPIER> OPTION> DSPLY-SW> FXMSG-SW
CNTR-SW Init parts counter estimated life value
Details To return the estimated life value of parts counter to the initial value.
Use case Upon user’s request
Adj/set/operate method 1) Enter 0, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0: Returned to the initial value
Default value 0
DMAX-DAY Set D-max control execution frequency
Details To set the frequency of D-max control that is executed after a specified
number of sheets is fed.
When 0 is set, the execution frequency of D-max control is decreased
by half.
Use case When density varies at the time of making a large number of outputs
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Half, 1: Normal
Default value 1