Canon imagePASS-P1 Service Manual Download Page 60

Page: 60 / 70

Check Items before
Installation

The IP addresses for

communication between the host
machine and equipment are set
automatically

1. Turn ON the main power switch of the host machine.

2. Set the value in the following service mode (Level 1)

to "3".

• COPIER > OPTION >INT-FACE > IMG-CONT

3. Exit from Service Mode.

4. Turn OFF the main power switch of the host

machine.

Securing space for installation

Be sure to secure the space for installing this equipment as
shown in the figure. The space of 200 mm or more from the
back of this equipment is necessary.

200 mm or more
(8in)

Equipment

Rearside

Frontside

Installation Outline Drawing

Checking the Contents

Stepped

Screw; M4

Screw with

Toothed Washer; M4x8

Crossover Ethernet
Cable (0.5 m) x1

Straight Ethernet Cable (3.0 m)

(for network connection) x1

• Including guides

7. INSTALLATION PROCEDURE

Summary of Contents for imagePASS-P1






































































Search results

Summary of Contents for imagePASS-P1

Reviews:

Canon imagePASS-P1, Service Manual, Page: 60 / 70

Search results

Summary of Contents for imagePASS-P1

Reviews: