manualshive.com logo in svg

Canon imagePASS-P1, Service Manual, Page: 57 / 70

Share
Download
Canon imagePASS-P1 Service Manual Download Page 57

Specifications

The imagePASS has, or makes use of, the following features.

Hardware features

• 2.7GHz Intel Pentium dual core G1820 CPU
• 2GB DIMM
• Hard disk drive (500GB)
• 4 USB2.0 ports
• 2 USB3.0 ports
• 10BaseT/100BaseTX/1000BaseT network port for network printing
• 10BaseT/100BaseTX printer port for a Ethernet cable to the printer
• 3V manganese dioxide lithium coin cell battery (Panasonic CR2032 or equivalent)
• Dedicated power supply
• Power switch

Physical specifications

• Operating Environment:

Temperature: +10°C to +40°C
Relative Humidity: 10%-85% (non-condensing)

• Power Supply Rating: 100 -240V, 50-60Hz, 2-4A
• Power Consumption: 100W (typical)
• Dimensions (Depth x Width x Height):

9.3 cm (3.5 in.) x 28.5 cm (11.2 in.) x 29.5 cm (11.7 in.)

• Weight: 4.3 kg (9.5 lb.)

Networking and connectivity

The imagePASS has the following networking features:

• Supports AppleTalk and TCP/IP protocols simultaneously
• RJ-45 Ethernet LAN port for twisted pair (10BaseT/100BaseTX/1000BaseT) network connection

NOTE:

The latest user software must be installed onto all computers that print to the imagePASS. Using incompatible versions of the
system and user software may result in system problems. For more information, see the user documentation.

Safety and emissions compliance

The imagePASS has been certified to meet or surpass the following standards:

• Safety approvals

• IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am2:2013
• UL 60950-1:2007 R10.14 (TUV NRTL)
• CAN/CSA C22.2 No. 60950-1:2007 +A1:2011 +A2:2014 (TUV NRTL)
• GS Mark by TUV, EN60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013

• EMC approvals

• FCC Title 47, Part 15 Subpart B, Class B- NA
• ICES-003, Issue 5, August 2012, Class B-NA
• EN55022:2010/AC:2011 (EU) Class B
• VCCI (JPN) Class B
• RCM Mark (Australia and New Zealand)- Class B
• EN61000-3-2: 2014
• EN610003-3: 2013
• EN55024:2010 (EU)

6. SPECIFICATIONS

52

Summary of Contents for imagePASS-P1







































































Reviews:

No comments